This part of GB 17799 specifies EMC emission requirements of electrical and electronic apparatus intended for use in residential, commercial and light-industrial environments.
This part is applicable to the frequency range 0 Hz to 400 GHz. No measurement needs to be performed at frequencies where no requirement is specified.
This generic EMC emission of this part is applicable if no relevant dedicated product or product-family EMC emission standard exists.
This part applies to apparatus intended to be directly connected to a low-voltage public mains network or connected to a dedicated DC source, which is intended to interface between
the apparatus and the low-voltage public mains network. This standard applies also to apparatus which is battery operated or is powered by a non-public, but non-industrial, low-voltage power distribution system if this apparatus is intended to be used in the locations described below.
The environments encompassed by this standard are residential, commercial and light-industrial locations, both indoor and outdoor. The following list, although not comprehensive, gives an indication of locations that are included:
Residential properties, for example houses, apartments;
Retail outlets, for example shops, supermarkets;
Business premises, for example offices, banks;
Areas of public entertainment, for example cinemas, public bars, dance halls;
Outdoor locations, for example petrol stations, car parks, amusement and sports centers;
Light-industrial locations, for example workshops, laboratories, service centers.
Locations that are characterized by being supplied directly at low voltage from the public mains network are considered to be residential, commercial or light-industrial.
The object of this standard is to define the emission test requirements for apparatus defined in the scope in relation to continuous and transient, conducted and radiated disturbances.
The emission requirements have been selected so as to ensure that disturbances generated by apparatus operating normally in residential, commercial and light-industrial locations do not exceed a level which could prevent other apparatus from operating as intended. Fault conditions of apparatus are not taken into account. Not all disturbance phenomena have been included for testing purposes in this standard but only those considered as relevant for the equipment covered by this standard. These requirements represent essential electromagnetic compatibility emission requirements.
Requirements are specified for each port considered.
Note 1: Safety considerations are not covered by this standard.
Note 2: In special cases, situations will arise where the levels specified in this standard will not offer adequate protection; for example where a sensitive receiver is used in close proximity to an apparatus. In these instances, special mitigation measures may have to be employed.
Note 3: As the requirements in this standard are more stringent than the requirements in GB 17799.4, equipment fulfilling the requirements of this standard will also comply with the requirements of GB 17799.4.
2 Normative References
The following documents are indispensable for the application of this document. For dated references, only the dated editions apply. For undated references, the latest editions (including any amendments) apply.
GB/T 6113.102-2008 Specification for radio disturbance and immunity measuring apparatus and methods — Part 1-2: Radio disturbance and immunity measuring apparatus-Ancillary equipment — Conducted disturbances (IEC/CISPR 16-1-2:2006, IDT)
GB/T 6113.402-2006 Specification for radio disturbance and immunity measuring apparatus and methods — Part 4-2: Uncertainties, statistics and limit modelling — Measurement instrumentation uncertainty (IEC/CISPR16-4-2:2003, IDT)
GB 9254-2008 Information technology equipment — Radio disturbance characteristics — Limits and methods of measurement (IEC/CISPR 22:2006, IDT)
IEC 60050-161 International Electrotechnieal Vocabulary (IEV) — Chapter 161: Electromagnetic compatibility
IEC 61000-3-2:2005 + Amendment 1:2008 + Amendment 2:2009 Electromagnetic compatibility(EMC) — Limits — Limits for harmonic current emissions(equipment input current ≤16 A per phase)
IEC 61000-3-3:2008 Electromagnetic compatibility (EMC) Limits — Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤16 A per phase and not subject to conditional connection
IEC 61000-3-11:2000 Electromagnetic compatibility (EMC) — Limits Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems — Equipment with rated current ≤75 A and subject to conditional connection
IEC 61000-3-12:2004 Electromagnetic compatibility (EMC) — Limits — Limits for harmonic currents produced by equipment connected to public low — voltage systems with input current >16 A and ≤75 A per phase
IEC 61000-4-20:2010 Electromagnetic compatibility (EMC) — Testing and measurement techniques — Emission and immunity testing in transverse electromagnetic (TEM) waveguide
IEC/CISPR 14-1:2005 + Amendment 1:2008 Electromagnetic compatibility — Requirements for household appliances, electric tools and similar apparatus — Part 1: Emission
IEC/CISPR 16-1-1:2010 Specification for radio disturbance and immunity measuring apparatus and methods — Part 1-1: Radio disturbance and immunity measuring apparatus — Measuring apparatus
IEC/CISPR 16-1-4:2007 + Amendment 1:2007 Specification for radio disturbance and immunity measuring apparatus and methods — Part 1-4: Radio disturbance and immunity measuring apparatus — Ancillary equipment — Radiated disturbances
IEC/CISPR 16-2-1:2008 Specification for radio disturbance and immunity measuring apparatus and methods — Part 2-1: Methods of measurement of disturbances and immunity — Conducted disturbance measurements
IEC/CISPR 16-2-3:2006 Specification for radio disturbance and immunity measuring-apparatus and methods — Part 2-3: Methods of measurement of disturbances and immunity — Radiated disturbance measurements
3 Terms and Definitions, Abbreviations
3.1 Terms and Definitions
For the purposes of this document, the terms and definitions given in IEC 60050-161, as well as the following apply.
3.1.1
