This standard specifies the technical conditions, inspection methods, test rules, mark, package and storage of continuous and intermittent oil feeding device in centralized lubrication system of numerical control machine tools.
This standard is applicable to the numerical control machine tools, precision machined tools, and continuous and intermittent oil feeding device in lubrication system taking the refined mineral oil with viscosity 22mm2/s~100mm2/s as the working medium, and is also applicable to the lubricating oil feeding device of general machine tools and mechanical equipment.
2 Normative References
The following standards contain provisions which, through reference in this text, constitute provisions of this standard. For dated reference, subsequent correctionments to (excluding correction to), or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of these documents is applicable. For undated normative references, the latest edition is applicable to this standard.
GB/T 191 "Packaging-Pictorial Marking for Handling of Goods" (GB/T 191-2000, eqv ISO 780:1997)
GB 5226.1 "Safety of Machinery-Electrical Equipment of Machines-Part 1: General Requirements"(GB 5226.1-2002, IEC 60204-1: 2000, IDT)
GB/T 7632 "Recommendations for the Choice of Lubricants for Machine Tools" (GB/T 7632-1987, neq BS 5063:1982)
JB/T 7943.1 "General Specification for Lubrication Systems and Elements"
3 Requirements
3.1 Basic Requirements
3.1.1 The basic parameters of the oil feeding device and elements shall be in accordance with those specified in JB/T 7943.1; the electrical system shall meet the requirements of GB 5226.1. The performance of all elements shall meet the requirements of the relevant standards and the design.
3.1.2 The fluid used for the oil feeding device shall be in accordance with those specified in GB/T 7632 and fluid requirements of the host machine; the used fluid shall be filtered carefully; the filter with filtering fineness no less than 10μm shall be installed in the system to control the cleanliness of the fluid.
3.1.3 For the oil feeding device performing the centralized lubrication through oil separator or distributor, the oil feed capacity of each lubrication point shall be packed.
3.1.4 The oil feeding device shall be equipped with pressure regulation and safety protection devices; the intermittent oil feeding device shall be installed with work-cycle regulating control device; the continuous oil feeding device shall be installed with the flow control device.
3.1.5 The oil feeding device shall be equipped with the pressure gauge with damping accuracy no less than Level 2.5 and measuring range equal to 1.5~2 times of the oil feeding system pressure.
3.1.6 In order to ensure the normal operation of the machine tools; the oil feeding device shall be of automatic alarm when the fluid is lower than the lowest oil level or the lubrication is affected owing to the fault of the lubrication device.
3.1.7 The oil tank of the oil feeding device shall be installed with air cleaner; the lowest position of the oil tank shall be installed with the oil drain hole for rapid oil drainage.
3.1.8 The whole oil feeding device shall be of esthetic appearance and be convenient for installation and maintenance.
3.1.9 The oil feeding device with special requirements shall be negotiated by the supply and demand parties.
JB/T 7452-2007 — Standards cited
JB/T 7452-2007 — Cited by
Use of cookies on this website:
We use strictly necessary cookies to make our site work. We would also like to set optional analytics cookies
to help us improve it, and targeting cookies. We won't set optional cookies unless you enable them.
For more detailed information about the cookies we use, see our
Cookies Notice.
By clicking "Accept all cookies", you agree to the storing of cookies on your device for the purposes set out
in our Cookies Notice. Click "Reject non-essential" to refuse optional cookies.
Strictly necessary cookies are always active and cannot be disabled.
Cookie Consent Manager
Your Privacy
Websites may store or retrieve information on your browser, mostly in the form of cookies.
This information might be about you, your preferences, or your device and is mostly used to make
the site work as you expect it to. The information does not usually directly identify you, but it
can give you a more personalized web experience. Because we respect your right to privacy, you can
choose not to allow some types of cookies. Click on the different category headings to find out more
and change our default settings. However, blocking some types of cookies may impact your experience
of the site and the services we are able to offer.
These cookies are required for the operation of our website and use of its features, and therefore
cannot be switched off in our systems. They are usually only set in response to actions made by you
which amount to a request for services, such as setting your privacy preferences, logging in, or
filling in forms.
Functional Cookies
These cookies are optional and are used to remember the choices you have made.
These cookies are optional and are used to collect information on how visitors use our website.
Targeting Cookies
These cookies may be set to deliver advertising that is more relevant to you and your interests,
or to measure advertising effectiveness. California residents may opt out of the sale or sharing
of personal information via Do Not Sell/Share.
If this site does not currently run advertising pixels, enabling this category has no effect until such tools are added.